Beneteau > Monotypes Figaro Bénéteau II

Características:

Arquitecto naval:
Eslora (m.): 10.15 m (33’)
Manga (m.): 3.43 m (11’3”)
Desplazamiento (kg.): 3600 kg (7,936 lbs)
Carburante (l.):
Agua dulce (l.):
Potencia motor (cv): 14 KW (19 HP)
Propulsión:
Certificado CE:

HULL
Balsa cored sandwich, multiaxial E-glass, vinylester resin made by infusion techniques
Viewing porthole for the keel and the propeller
Cone-shaped keel casing

STRUCTURE
Polyester structure of the open inner lining type, structural bonding and repetition of the stratification in areas under strain.
Infusion made structural bulkheads in balsa cored sandwich, structural bonding of the hull and repetition of stratification
Watertight bulkhead to the aft with Lewmar 44 x 44 hatch to gain access from inside.

DECK
Balsa cored sandwich deck, multiaxial E-glass, vinylester resin made by infusion moulding
CP reinforcements for fittings
Screwed down toerail between the deck and hull
1 44 x 44 Lewmar hatch to the bow
2 lateral portholes bonded to the coachroof sides
1 T0 hinged ventilation panel in the cabin
2 T 0 hinged portholes on the vertical side of the cockpit
1 Dorade style ventilator in the cabin
1 drainage hole for passing the hoisting sling through
2 stainless steel hand rails

INTERIOR FITTINGS

GALLEY
Polyester storage unit with 1 burner gimballed stove to starboard
Polyester storage unit with plastic basin

NAVIGATION STATION
Fixed chart table unit with seat and instrument holder

SALON
2 watch seats on either side of the hatchway
2 aluminium framed berths with canvas on either side underneath the cockpit
Stainless steel companionway ladder with wooden steps

ENGINE / ELECTRICITY
Volvo 2030 engine
Power pack including tank, batteries, engine control panel,
Rotomoulded 40 L diesel tank
140 amph alternator
Load dispatchor
Propellor shaft/bracket  propulsion
Retractable clutch lever in the cockpit
Anti-fouling on the shaft
Folding propellor
1 70 amph starter battery
2 140 amph engine compartment batteries
Electrical panel with 7 functions on instrument panel
Electrical panel with 7 functions in the companionway
Manual bilge pump
Electrical bilge pump

BALLAST
1 260 L ballast in stratified polyester on portside and starboard plating with inspection hatches
Diaphragm 45 L/minute electric filling pump, which can be handled from the cockpit.
Gravitational transfer through Ø 125 mm pipe
Transfer sluice in the bottom of the cockpit near the helm
Filling and draining bailer

EXTERIOR FITTINGS
2 T44 Lewmar primary winches
Transverse genoa car with vertically adjustable ball-bearing sheave
Clews inside for tweaker tuning
2 genoa flying blocks
Mainsail ball-bearing traveller track on aluminium base
Mainsail tackle with fine tune tackle leading back to the helmsman
Traveller tuning leading back to the helmsman
Cascade kicking strap tackle
Mainsail Cunningham blocks
Cascade running blocks and tackles or split backstays leading to the helmsman
4 spinnaker blocks
Spinnaker tweaker blocks
Kicking strap spinnaker pole blocks
Helmsman adjustable toe-clip bracket
Stainless steel extendable tiller
2 manoeuvring winches on T40 Lewmar coachroof
8 halyard and manoeuvring blocks and jammers on protective companionway bulwark
6 sheaves organizer astern of jammers
2 mini towers for cascade tuning of the vang
2 cleats on coachroof for tuning the spinnaker pole downhaul
1 mainsail Cunningham cleat
1 mainsail foot cleat
1 pulpit with emergency lights
2 stern pulpits
8 stanchions with struts
Deck eyes to tie safety harness to in the cockpit
1 bulkhead compass
2 simple winch crank handles

RIGGING

MAST
Carbon mast in two sections painted white with bolt rope fixed to deck
Spreaders at an angle of 20° to the stern
Red, white and blue lights on masthead
Flexible batten on masthead for forestay downwash
Exterior shroud chain plates
Lower shroud sunken chain plates for the jib to pass through


BOOM
Anodized aluminium boom with rear mainsheet system.
Foot tuning by boom tackle
Sheet and vang blocks on straps
Rigid boom kicker vang

SPINNAKER POLE
Ø 75mm carbon spinnaker pole
Automatic end pieces
Pennants

STANDING RIGGING
Discontinuous rigging rod
Dyneema backstay
Full Nord Foil foresaty

RUNNING RIGGING
Complete mainsail tackle
Complete kicking strap
Complete jib and sheet tuning system
Spinnaker sheets
Spinnaker tweaker
Spinnaker pole downhaul
Mainsail halyards, 2 genoas/spinnakers, spinnaker pole uphaul
Complete backstay system with safety device

STEERING SYSTEM
Twin rudder with sandwich oar blade on stainless steel core
2 automatically aligning engine bearings with needle bearing
Main piece with aluminium crossbeam on automatically aligning engine bearings with needle
bearings.
Pilot guy on main piece
Aluminium tiller stops
Stainless steel extendable tiller

LEST
Composite cast iron lead with calibration flyweights
Epoxy resin protection injected from the exterior into a mould
Assembly by bell-shaped joining in a moulding casing